GetAirlineCare

How To Adjust Skateboard Wheels

Introduction

Skateboards are easy to maintain, but they do require some care. If you want to get the most out of your board, you should know how to adjust skateboard wheels.

Skateboarding is fun and helps kids build confidence and coordination skills. But sometimes things don’t go according to plan: maybe your wheels aren’t straight enough or maybe there’s too much wobbling when riding down hills. Fortunately, adjusting skateboard wheels isn’t difficult at all; it just requires a few simple steps that anyone can follow!

Do you have a skateboard but it doesn’t work as well as you’d like? There are things you can do to make your board better.

If you have a skateboard but it doesn’t work as well as you’d like, there are some things that can be done to make your board better.

The skateboard is the foundation of a great ride. The wheels are the most important part of the skateboard and they’re also the only part of your board that touches the ground. So when these parts aren’t adjusted properly, your ride will feel choppy or slow down considerably after riding for awhile.

Adjusting your trucks can affect wheel fitment too; however, adjusting wheels is easy! All it takes is a Phillips head screwdriver (or appropriate tool) and some patience before getting out on the streets again—and with these tips below, making those adjustments should be simple enough!

  • Turn the nuts counter-clockwise using a wrench.
  • Remove the nuts from the axle and take off the wheel.
  • Use a screwdriver to adjust the truck of your board, if necessary (if it is, then you can skip ahead).
  • Put the wheels back on your skateboard, making sure that they’re centered, then secure them with the nuts tightened by hand or with your wrench (if you didn’t need to adjust anything).
See also  Can You Make Your Own Skateboard

Place your skateboard on a level surface and push down on one end. If it doesn’t move or wobble, then you’re good to go. If there is still a bit of movement, tighten the nuts by hand until the board is secure.

Adjust the wheels until they are almost touching the surface. Make sure the front of the skateboard is a few centimeters off the floor, too.

With the skateboard facing you, adjust the wheels until they are almost touching the surface. Make sure the front of the skateboard is a few centimeters off the floor, too.

Make sure that both wheels are centered within their trucks (wheel axles). If they’re not centered, it may affect how well your board rolls.

The next step is to tighten each truck’s axle nuts by hand. The nuts are usually found on the back of each truck, where the axle meets the board. Use an Allen wrench to tighten them evenly in a star pattern until they’re snug but not too tight.

Determine bumpiness.

Determine bumpiness.

Bumpiness is a common ailment among skateboarders, especially those who haven’t been skating for long. It’s typically caused by loose or worn bearings, which can be fixed by adjusting the skateboard wheels. If you’re new to skating and want to avoid bumps in the road, follow these steps:

  • Check your bearings. The first thing you should do when you notice your board has become bumpy is check your bearings. If they’re loose or worn down, try tightening them using an Allen wrench (if applicable) before moving on to step two!
  • Tighten and loosen screws as needed based on what kind of trucks you have on your board; different brands require different styles of screws so make sure that yours matches up with the instructions provided in our blog post here!
See also  Can Electric Skateboards Go Uphill

Adjust your trucks.

Next, you’ll need to adjust your trucks. The truck is the part of the skateboard that allows you to turn by leaning and pushing on one foot while the other foot stays planted on board. If one truck is higher than the other, you will have to lean more to turn in that direction. To fix this issue, loosen both nuts on your wheels and place them back onto their axles at the same level as each other.

Change the bushings on your skateboard.

You may have heard about “bushings” in skateboarding. They’re the little cups that go around your wheels, and they help control how much you can turn and lean on your board.

There are two basic types of bushings: soft and hard. Soft bushings are less firm, which means they give you more turning power but less stability. Harder bushings are more stable but less agile, so they’re great for cruising around town or carving down hills at high speeds (or doing tricks). If you’re just a beginner looking to cruise around town on your first skateboard, soft bushings will probably work best!

If your board isn’t doing what it should be after adjusting the wheels and trucks, chances are good that one of those three things—the wheel size; wheel tension; or bushing type—is causing problems for you!

Use a speedring.

Speedrings are a small piece of metal that attaches to the trucks. They allow you to adjust the position of your wheels and thereby change their height.

See also  How To Maintain Skateboard

Speedrings come in different sizes, and they come with different mounting hardware. Some speedring kits will include two rings (the smaller one goes on top), whereas others have only one ring that fits both sides of the board (so you can flip it over).

Speedring kits are available for all types of skateboard decks, including drop-throughs, penny boards, and cruisers.

Tighten the wheels, not the trucks, to eliminate uneven surfaces when skating.

  • Tighten the wheels, not the trucks, to eliminate uneven surfaces when skating.
  • Turn the nuts counter-clockwise using a wrench.
  • Remove the nuts from the axle and take off the wheel.
  • Use a screwdriver to adjust your truck’s height or angle on your board.
How to Adjust Your Skateboard Setup - Trucks & Wheels

Conclusion

Skateboarding is a fun sport that can be enjoyed by anyone. If you want to take your skills to the next level, then learning how to adjust skateboard wheels is a great way to do so! By following these steps, you’ll be able to get the most out of your board and help make it last longer than ever before.

Leave a Comment